Veterinary ELISA Assay

Rat AT1R IgG Antibody ELISA

$2,155.00

This Rat AT1R IgG Antibody ELISA is designed for the determination of Rat antibodies (IgG) against the Angiotensin II receptor subtype I in serum and plasma. The Eagle Biosciences Rat Anti Angiotensin Receptor 1 (ATR1) IgG Antibody ELISA Assay Kit is for research use only and not to be used in diagnostic procedures.

SKU: AT121-K01 Categories: , Tags: ,

Rat AT1R IgG Antibody ELISA

The Rat AT1R IgG Antibody ELISA is For Research Use Only

Size: 1×96 wells
Sensitivity: Cut-off
Dynamic Range: 1.25 – 40 U/ml
Incubation Time: 3.5 hours
Sample Type: Serum, Plasma
Sample Size: 100 µL
Alternate Name: Rat Anti Angiotensin II Receptor 1 IgG Antibody ELISA Assay Kit, Rodent Anti Angiotensin II Receptor 1 IgG Antibody ELISA Assay Kit
Controls Included

Sample Preparation and Storage
Dilute the samples with diluent using 1:100 dilution (eg. 5 µl serum or plasma + 495 µl diluent). If samples generate values outside the standard curve, the dilution factor may be quite varied. Store the undiluted samples at room temperature for 48 hours, 2-8°C 4-days, and long-term storage for up to 12 months at –20 °C. Avoid repeated freeze-thaw cycles.

Assay Principle

The Eagle Bioscience’s Rat Anti Angiotensin Receptor 1 (ATR1) IgG Antibody ELISA Assay Kit is an antibody screening test. Angiotensin II Receptor has been pre-coated onto a microtiter plate. During the first incubation the rat anti-Angiotensin II receptor 1-IgG-Antibodies of the samples are immobilized on the plate. The autoantibodies are detected with a POD labelled anti-Rat IgG antibody. In the following enzymatic substrate reaction the intensity of the colour correlates with the concentration and/ or avidity of anti-Angiotensin II receptor 1-antibody (IgG).

Related Products

Rat Anti Angiotensin II Receptor 1 (AT1R) IgM Antibody ELISA Assay Kit
Rat Anti Endothelin Receptor A IgG Antibody ELISA Assay Kit
Rat Anti-ETA IgM Antibody ELISA

Additional Information

Assay Procedure

  1. Prepare all reagents and samples as directed in the previous section.
  2. Pipette 100 µl of diluted samples, standards, controls or diluent (as blank) into the wells.
  3. Seal wells with adhesive strip and incubate for 2 hours at 2-8°C temperature.
  4. Aspirate fluid from wells and wash three times with 300 µl wash buffer.
  5. After the last wash, invert the plate and tap on a clean paper towel.
  6. Dispense 100 μl of diluted HRP conjugate into each well.
  7. Seal wells with adhesive strip and incubate for 1 hour (with shaking) at room temperature.
  8. Repeat the wash as in step 4.
  9. Dispense 100 µl of TMB substrate solution into each well.
  10. Incubate for 20 minutes at room temperature in the dark.
  11. Add 100 µl of stop solution to each well.
  12. Determine the absorbance within 30 minutes at 450 nm. A reference wavelength of 620 nm/690 nm is recommended.

Typical Standard Curve

Rat AT1R IgG Antibody ELISA

Package Inserts

Please note: All documents above are for reference use only and should not be used in place of the documents included with this physical product. If digital copies are needed, please contact us.

Product Citations